 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SL358 Low Power Dual Operational Amplifier The SL358 contains two independent high gain operational amplifiers with internal frequency compensation. The two op-amps operate over a wide voltage range from a single power supply. Also use a split power supply. The device has low power supply current drain, regardless of the power supply voltage. The low power drain also makes the SL358 a good choice for battery operation. When your project calls for a traditional op-amp function, now you ORDERING INFORMATION can streamline your design with a simple single power supply. Use SL358N Plastic ordinary +5VDC common to practically any digital system or personal SL358D SOIC computer application, without requiring an extra 15V power supply just TA = 0 to 70 C to have the interface electronics you need. for all packages. The SL358 is a versatile, rugged workhorse with a thousand-andone uses, from amplifying signals from a variety of transducers to dc gain blocks, or any op-amp function. The attached pages offer some recipes that will have your project cooking in no time. * Internally frequency compensated for unity gain * Large DC voltage gain: 100dB * Wide power supply range: 3V ~ 32V (or 1.5V ~ 16V) * Input common-mode voltage range includes ground * Large output voltage swing: 0V DC to VCC-1.5V DC * Power drain suitable for battery operation * Low input offset voltage and offset current * Differential input voltage range equal to the power supply voltage LOGIC DIAGRAM PIN ASSIGNMENT PIN 4 = GND PIN 8=VCC SLS System Logic Semiconductor SL358 MAXIMUM RATINGS * Symbol VCC Power Supply Voltages Single Supply Split Supplies VIDR VICR ISC TJ Tstg Input Differential Voltage Range (1) Input Common Mode Voltage Range Output Short Circuit Duration Junction Temperature Plastic Packages Storage Temperature Plastic Packages IIN TL * Parameter Value Unit 32 16 32 -0.3 to 32 Continuous V V V 150 C C -55 to +125 50 260 mA C Input Current, per pin (2) Lead Temperature, 1mm from Case for 10 Seconds Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: : - 7 mW/C from 65 to 125C Notes: 1. Split Power Supplies. 2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATING CONDITIONS Symbol VCC TA DC Supply Voltage Operating Temperature, All Package Types Parameter Min 2.5 or 5.0 0 Max 15 or 30 +70 Unit V C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V ). CC Unused outputs must be left open. SLS System Logic Semiconductor SL358 DC ELECTRICAL CHARACTERISTICS(TA=0 to +70C) Guaranteed Limit Symbol VIO VIO/T IIO IIO/T IIB VICR ICC A VOL VOH VOL CMR PSR CS ISC Isource Isink Parameter Maximum Input Offset Voltage Input Offset Voltage Drift Maximum Input Offset Current Input Offset Current Drift Maximum Input Bias Current Input Common Mode Voltage Range Maximum Power Supply Current Minimum Large Signal Open-Loop Voltage Gain Minimum Output HighLevel Voltage Swing Maximum Output LowLevel Voltage Swing Common Mode Rejection Power Supply Rejection Channel Separation Maximum Output Short Circuit to GND Minimum Source Output Current Minimum Output Sink Current Test Conditions VO=1.4V VCC=5.0-30V;RS=0 VICM=0V to VCC-1.7V RS=0, VCC=30V VCC=5.0V RS=0, VCC=30V VCC=5.0V VCC=30V RL=,VCC=30V,V0=0V RL=,VCC=5V,V0=0V VCC=15V, RL2K VCC=30V,RL=2K VCC=30V,RL=10K VCC=5V,RL=10K VCC=30V, RS=10K VCC=30V f=1KHz to 20KHz,VCC=30V VCC=5.0V VIN+=1V, VIN-=0V, VCC=15V, V0=0V VIN+=0V, VIN-=1V, VCC=15V, V0=15V VIN+=0V, VIN-=1V, VCC=15V, V0=0.2V All VINGND or V-Supply (if used) 10 5 12* VCC* 65* 65 -120* 60* 15 26 27 20 0 10 -500 28 3 1.2 V/mV V mV dB dB dB mA mA mA A V 7.0 150 Min Typ Max 9.0 Unit mV V/C nA pA/C nA V mA VIDR *=@25C Differential Input Voltage Range SLS System Logic Semiconductor SL358 TYPICAL PERFORMANCE CHARACTERISTICS Figure 1.Input Voltage Range Figure 2. Open-Loop Frequency Figure 3. Large-Signal Frequency Response Figure 4. Small-Signal Voltage Follower Pulse Response (Noninverting) Figure 5. Powe r Supply Current versus Power Supply Voltage Figure 6. Input Bias Current versus Power Supply Voltage SLS System Logic Semiconductor |
Price & Availability of SL358N
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |